What are your ideas on How to Install a Bathtub?
Setting up a bathtub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily accessible, the project can relocate easily; if you have to open up a wall surface to remove the old bathtub and also place the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This article will assist you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices as well as product checklist should comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the faucets have been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers are in area between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile tap port to the ideal supply pipe by making a compression join; after that do the same for the other faucet.
Switch on the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub as well as also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Ultimately, repair the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bath tub needs to wait until the tub has actually been made use of at the very least when as this will settle it into its last setting.
Planning for the Setup
First of all, the sustaining framework provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its last position.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, triggering the water to penetrate the wall in between the bath and the tiling, bring about difficulties with moisture and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack relatively early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads on How to Install a Bathtub, I was thinking sharing that piece of content was important. Enjoyed reading our blog entry? Please share it. Let somebody else locate it. We recognize the value of reading our article about Installing A Bathtub.
Explore Now